Thinkcar Thinkscan SD6(6 Systems) 5 special functions
Thinkcar Thinkscan SD6 is a new generation of mid-range product based on Android launched by THINKCAR with Software developed by LAUNCH Tech, with FREE SOFTWARE UPDATES for life. Thinkscan SD6 can perform diagnosis of 6 electronic control systems Thinkscan SD6 Supports ABS SRS ECM TCM BCM IC systems diagnostics:
1. ENG: Engine System
THINKSCAN SD6 Scanner tool helps you read fault codes and shows the definition of DTC , clear the error, and turn off the MIL (Engine Malfunction Indicator Light).The instantaneous change of real-time data information can quickly identify the problem of Engine components, which is helpful to find out the cause of engine system errors before sending your vehicle to a repair shop.
2. AT: Transmission System
THINKSCAN SD6 Auto code reader Thinkscan SD6 diagnostic scanner is an automatic Transmission service tool that supports reading/erasing codes, viewing live data, tell you the running status of the sensors, read the error and turning off the warning light, which is helpful to quickly and accurately locate faults and solve problems easily.
3. ABS：Anti-lock Braking System
The diagnostic tool THINKSCAN SD6 is available for accessing and performing car diagnostics on Anti-lock Brake Systems respectively Whether it is the brake pad deviation, the brake pad does not return to position, or other reasons of failure. It will read ABS fault codes and tell you what the problem is through a visual inspection of all brake components, and then clear the codes. For the safety of your family, please pay attention to the health of the brake system in time.
4. SRS: Supplemental Restraint System
This OBD2 scanner tool THINKCAR SD6 supports Airbag System Diagnostic (SRS) for most domestic and imported vehicles. This scan tool can check the errors and clear the codes, view real-time live data to monitor the SRS running status, and solve security risks.Extend the service life of airbags and improve vehicle safety.
5. IC: Instrument Cluster System
The Automotive Engine Scanner THINKCAR SD6 can quickly input signals to the instrument panel and read the fault information, and at the same time store the fault code of the faulty part. When it is confirmed that the instrument panel is faulty, the instrument panel code error should be detected and cleared, which can better protect the driving safety of the car owner.
6. BCM: Body Control Module
The THINKCAR SD6 automotive Scan tool enables you to read data, calculate and analyse the data from the BCM which also generally controls the immobiliser. Calculate the data required to execute the command according to the information parameters, compare the input information with the standard value. Finally, output vehicle fault information and complete fault correction. This helps to enhance the safety, comfort and convenience of the car.
Thinkscan SD6 Supports 28 Reset Function (Choose 5):
Pls note : You can choose 5 Reset Function Free (Yours for life), for extra reset functions you can purchase additionally for US$29.95 per reset function (±R500)
1 Oil Reset
The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset themileage or driving time to zero after the maintenance, so the maintenance light will go out and the systemwill start a new maintenance cycle.
2 Elec.Throttle Adaption
Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learningvalue of the ECU returns to the initial state.By doing these, the movement of the throttle (or idle motor)can be more accurately controlled, thus adjust the intake volume.
3 Steering Angle Reset
To reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference, the ECU can calculate the accurate angle for left and right steering.After replacing the steering angle position sensor, replacing steering mechanical parts (such as steeringgearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recoveringcar body, you must reset the steering angle.
4 Battery Matching
This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, inwhich the original low battery fault information will be cleared and battery matching will be done.
5 ABS Bleeding
When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system torestore ABS brake sensitivity. lf the ABS computer,ABS pump, brake master cylinder, brake cylinder, brakeline, or brake fluid is replaced, the ABS bleeding function must be performed to bleed the ABS.
6 Brake-pad Reset
lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to theon-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms.
7 DPF Regeneration
DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuouscombustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reducePM ignition combustion) to stabilize the filter performance.
8 Gear Learning
The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computerto more accurately diagnose engine misfires. lf gear learning is not performed for a car equipped withDelphi engine, the MlL turns on after the engine is started.The diagnostic device detects the DTC P1336’gear not learned’. In this case, you must use the diagnostic device to perform gear learning for the car.After gear learning is successful, the MIL turns off. After the engine ECU, crankshaft position sensor, orcrankshaft flywheel is replaced, or the DTC ‘gear not learned” is present, gear learning must be performed.
9 IMMO Service
To prevent the car being used by unauthorized keys, the anti-theft key matching function must beperformed so that the immobilizer control system on the car identifies and authorizes remote control keysto normally use the car. When the ignition switch key, ignition switch, combined instrument panel,ECu,BCM, or remote control battery is replaced, anti-theft key matching must be performed
10 Injector Coding
Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder soas to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced,injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identifyinjectors to accurately control fuel injection.
11 TPMS Reset
After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting function must be performed to reset tire pressure and turn off the tire pressure MIL.Tire pressure resetting must be performed if tire pressure is too low, tire leaks, tire pressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged, and tire is replaced for the car with tire pressure monitoring function.
12 Suspension Matching
This function can adjust the height of the body. When replacing the body height sensor in the air suspension system, or control module or when the vehicle level is incorrect, you need to perform this function to adjust the body height sensor for level calibration.
13 AFS Reset
This feature is used to initialize the adaptive headlamp system.According to the ambient light intensity, the adaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjust the headlamp lighting angle while monitoring the vehicle speed and body posture.
14 A/T Learning
Many more functions 28 in total.